DIN EN 10216-2 PDF

Buy DIN EN SEAMLESS STEEL TUBES FOR PRESSURE PURPOSES – TECHNICAL DELIVERY CONDITIONS – PART 2. DIN EN Seamless steel tubes for pressure purposes – Technical delivery conditions – Part 2: Non-alloy and alloy steel tubes with specified elevated. ​Manufacturing program with average wall thickness (EN ). Vallourec supplies seamless steel tubes for pressure purposes in accordance with.

Author: Maurr Grosar
Country: Samoa
Language: English (Spanish)
Genre: Software
Published (Last): 9 February 2017
Pages: 210
PDF File Size: 7.25 Mb
ePub File Size: 2.70 Mb
ISBN: 993-1-62110-877-6
Downloads: 32801
Price: Free* [*Free Regsitration Required]
Uploader: Shar

Page 20 EN ENNon-destructive testing of steel tubes – Part 1: All dressed areas shall blend 102162 into the contour of the tube.

Description of DIN EN and | Sunny Steel Enterprise Ltd.

eh Page 16 EN Automatic electromagnetic testing of seamless and welded except submerged arc welded ferromagnetic steel tubes for verification of hydraulic leak tightness.

NOTE This Part of EN may also be applied for tubes of non-circular cross section; necessary modification should be agreed a the time of ordering.

Tubes shall be suitable for hot and cold bending provided the bending is carried out in an appropriate manner. Non-alloy and alloy steel tubes with specified low temperature properties Specifies the technical delivery conditionsin two categories for seamless tubes of circular crossection, made with specified low temperature properties, made of non-alloy and alloy steel….

Add to Alert PDF.

Stainless steel tubes; German version EN NOTE When welding tubes produced in accordance with this Part of this ENaccount should be taken of the fact that the behaviour of the steel during and after welding is dependent not only on the steel, but also on the applied heat treatment and the conditions of preparing for and carrying out the welding.

  ASUS P8P67-M PRO MANUAL PDF

ENMetallic materials – Tensile testing – Part 1: Automatic full peripheral ultrasonic testing of seamless and welded except submerged arc welded steel tubes for the detection of longitudinal imperfections. At the manufacturer’s discretion: The test pressure shall be held for not less than 5 s for tubes with di outside diameter D less than or equal to mm and for not less than 10 s for tubes with an outside diameter greater than mm.

Inspection and testing to be carried out are summarised in table Normally, the finish and surface condition shall be such that any 1021-2 imperfections requiring dressing can be identified. ENMetallic materials – Tubes – Ring expanding test. The tubes shall be delivered in accordance withone of the following sets of dimensions as specified at the time of ordering: A comma is used as the decimal marker.

EN – PIPES FOR PRESSURE | BOILER TUBES | RELIABLE STEEL DISTRIBUTORS

The wall thickness shall be measured away from the tube ends in accordance withan agreed procedure. In addition, for inspection document 3. Unless option 15 is specified the wall thickness shall be measured at both tube ends.

X is the manufacturer’s mark; TC1 is the designation of the test category 1; Y is the cast number or a code number; Z1 is the mark of the inspection representative; Z2 is the identification number.

  DANIEL NEGREANU POWER HOLDEM PDF

For the remaining steel grades the values were obtained from creep rupture strength values given in national and international standards b The creep rupture strength values given up to the elevated temperature listed in the table do not mean that the steel can be used in continuous duty up to the these temperatures. ENMetallic materials – Tubes – Drift expanding test. We have no amendments or corrections for this standard.

When an inspection document 1021-62. The marking shall include the following information: Standards Subscriptions from ANSI provides a money-saving, multi-user solution for accessing standards. The tube section shall be expanded with a conical tool until it breaks.

Description of DIN EN 10216 and 10217

The test temperature shall be specified at the time of ordering. Non-alloy steel tubes with specified room temperature properties Specifies the technical delivery conditions for two qualities, T1 and T2, of seamless tubes of circular cross section, with specified room temperature properties, made of non-alloy quality steel….

Proceed to Checkout Continue Shopping. The tubes of test category cin shall subjected to a non-destructive testing for the detection of transverse imperfections in accordance with Standards Subsctiption may be the perfect solution.

The tube shall withstand the test without showing leakage or visible deformation. Seamless steel tubes for pressure purposes — Technical delivery conditions — Part 5: